The Xbox 360 Red Ring of Death Repair

The only known Repair to permanently fix your Xbox 360 

For the Red Ring of Death Repair, Please Scroll Down.

This article is going to show you the only known Xbox 360 red ring of death repair that is currently available and how to do it. 

This repair will permanently fix the overheating issue inside of your Xbox 360 (which is the primary cause of the RROD). Upon doing so, you will be protecting and preventing your system not only from the RROD but from a handful of other errors associated with the Xbox 360 overheating.

Errors such as:

• 2 & 4 Red Light errors 
• Graphic Glitches 
• Freezeup's 
• and the E74 error code 

Can all be permanently solved with this simple repair. With the removal and prevention of all of these different errors, you will never have to worry when playing your 360 again. This xbox 360 red light repair is very beneficial and has been so for thousands of people who have already used it.

Click here to Discover the Xbox 360 Red Ring of Death Repair

Not requiring any technical experience on your part, and taking less than an hour, this will be the optimal choice for anyone seeking to remove the red ring from their Xbox 360 for good!.

Tools:

There are several tools needed to make the following repair. Many of these items are common household items, others may need to be purchased at a hardware store. You can get a list of all the necessary items at my, Xbox 360 repair parts section. 

1. Remove the Hard Drive

First you will want to remove the hard-drive. This is as simple as pressing the hard-drive release button and simply pulling it off the console.

2. Remove the Face-Plate   

The face plate is the next thing to come off. To do this, put your fingers into the USB port on the left side of the Xbox 360. Grab the casing and just pull up and the face plate will remove itself. Always be delicate when handling the plastic parts of the system..  

3. Remove Side-Panels 

The grey side panels are next, and you should first start with the site opposite to the hard-drive side. You will need to use a paper clip to get these guys off, and what you have to do is unhook the 6 tabs that are holding the ventilation shield in place. Just unhook and lift up to remove the first ventilation shield.

The opposite side of the 360

Simply lift the side panel while individually unlocking each tab with your paper clip.

Now for the hard-drive side. For the hard-drive side there are two tabs that are hidden. Look at the picture for an illustration of where the first two are. 

The hidden two are located where the hard-drive sat. In two little ports you will see them. Just stick the paper clip in here and unhook these tabs and pull up on the ventilation shield to remove it.

4. Remove Lower Casing 

Once the side panels are gone, the lower portion of the 360 has to come off. To do this, there are tabs that will need to be unhooked as shown in the illustration. Simply use your finger nail for the tabs located in the front, and your knife or pointy object for the 7 tabs in the back. Start with the backside first, and then do the front. 

Here are their locations:

 For the front tabs just use your finger nail to get them un-done.

When you've undone the tabs flip the 360 top-side (bottom side up) so the lower half can be removed.  

5. Remove Outer Screws

When you've removed the lower portion this what you will see:

The highlighted red and green circles are the specific screws that will need to be removed. To remove these screws use your Torx T-10.  To make the re-assembly process easier, be sure to keep all screws together.

I highly recommend that you get the entire repair course filmed in High Definition video to make this easier for you:

Click Here for the Xbox 360 Red Ring of Death Repair

    6. Eject Button Removal 

Now we are going to be removing the eject button. If you don't remove this before removing the top portion of the Xbox 360, this button will snap. That is why we are taking care of it now. To remove it just grab it and pull it up.

7. Remove The Top Casing 

Now that the eject button has been removed and the screws removed, go ahead and take off the top of the Xbox 360.

8. Remove DVD/CD Drive 

Now the DVD drive will need to be removed. Just lift it up, and unhook it from the back. Piece of cake.

9. Fan Shroud & Fan Removal 

Now we need to take out the Fan Shroud. Simply unhook it from it's release tab.

Now the actual fans can be removed. Simply disconnect the fans and pull them out from their placement.

To make sure your repair goes smooth like I highly recommend that you get the entire repair course below:

The Xbox 360 Red Ring of Death Repair Guide

10. Remove 8 X Screws 

Next we will need to remove the 8 screws holding the motherboard in place. Go ahead and use your T-8 to do this. Remember to keep your screws together.

11. Remove Light Cover 

Now the light cover needs to come off. Simply pull up on the top of it and it will come off easily. Be gentle.  

12. Remove RF Module 

Now we can remove the RF Module. To do this, use your T-8 to remove the 3 screws holding this in place. After that just pull on the board to release it.  will come right off.

13. Remove Mother-Board

Once all of this has been done. We can finally remove the motherboard. Simply grab the heat sinks and lift up on the motherboard. Make sure to handle this step with caution. If the motherboard doesn't come out then you have not removed everything properly. Go back to the following steps and make sure you've done everything. If everything done and it's still not coming out, make sure the motherboard isn't caught on something. 

14. Remove X-Clamps and Heat Sinks

Now we need to remove the infamous X-Clamps. Simply use your flat head screw driver to pry off each tip of the X-Clamp to remove it properly. Make sure to take your time when doing this.

Once both X-Clamps are removed, take the heats sinks off of the motherboard.

15.  Apply Thermal Compound

Now you are ready for the modification process. What you will need to do is remove the original thermal compound paste on the GPU and CPU with our new paste from the Xbox 360 parts section. Since this is a delicate process and requires precise instructions, make sure to use the The Xbox 360 Pro Gamer Edition for precise details on how to do this.

16. Re-Adjust Heat Sinks

Now that the thermal paste is on securely, we only have one more mod to do and were done! Told you it was easy! What you will have to do is use our screws and washers from the repair parts list to re-apply them to the Heat Sinks so they will be more properly situation and secure. Since this mod also requires precice instructions be sure to use the guide listed above to do this step properly. We can't have any room for mistakes, especially since we've gotten this far. 

17. Re-Assemble Console

After everything has been done, all mods properly applied you will effectively be finished with your xbox 360 red ring of death repair. The only thing left to do at this stage is to begin re-assembling your console. If however you'd like to repair and prevent several other errors from your console such as,

1 & 2 Red Light Errors,

Graphic Glitches,

Game Freezes,

and the E74 Error Code

Then there is one more small modification to be made. In order to do this mod be sure to use the guide illustrated above. It will show you everything you need to do in the proper detail and instructions that this general overview cannot provide. After that mod is made the repair guide will walk you through the entire re-assembly process to ensure that you get back to your game asap. 

Now this is the same process and repair that has already helped thousands of people. It's helped many people that I know personally, people that I've recommended it to, and it has been allowing 360 owners a successful repair for over 2 years.  Make sure to get this guide asap to get your console back in healthy condition today.  

Click Here to Get The Xbox 360 Red Ring of Death Repair Guide

Is your Xbox 360 Suffering from the Red Ring of Death? What if you could repair your system today in just 1 hour - would you want to know how?

If your answer to the above questions is yes, then I strongly recommend that you check out  The Xbox 360 Red Light Repair Guide.

This regularly updated essential guide is the GUARANTEED solution to some of the most common Xbox 360 errors that you can face. This guide will show you how to solve game freezes, graphic glitches,the E74 error code and more including the Red Ring of Death permanently. 

All images provided on behalf of  http://www.xbox360redlightfix.com